Material Safety Data Sheet
Click here to download the MSDS sheet in pdf form.
Issue date: November 9, 2012
SECTION 1 – Material Identification
| Product Name | Manufacturer’s Name | Emergency Phone | Address | Hazardous Material Description | Additional Hazard Classes | Chemical Family | Formula |
| Ceramic Coated Pipe | Stryker Steel Tube | (262) 367.4421 | 3400 W. Marshall Avenue, Suite 428 Longview, TX 75603 | Hazard No. (49CFR 172.101) | N/A | Metals | FeCMnPSS |
SECTION 2 – Ingredients
| CAS # | Chemical Name | PEL (mg/m3) | TLV (mg/m3) | %W | SARAIII |
| SEQ No-40-5 | Base Metal Iron (Fe) | None established | 5 | 92 | No |
| 1333-86-4 | Alloys – carbon | TWA 3.5 | TWA 3.5 | <1 | Yes |
| Aluminum 7429-90-5 | Metallic Coatings | None established | TWA 2 | <1 | Yes |
| 7439-46-5 | Manganese | None established | None established 02+2 | <1 | Yes |
| 1310-58-3 | Potassium | None established | 2 | <1 | Yes |
| 7446-09-5 | Sulfur | WA 5ppm, 13mg/m3 | TWA 2ppm, 5mg/m3 | <1 | Yes |
| 7440-4-3 | Silicon | None established | 10 | <1 | No |
| 7631-86-9 | Silicon Oxide Amorphous | 20 mppef | TWA 80mg/m3 +%5:02 | <1 | Yes |
| 7440-67-7 | Zirconium Oxide | TWA 5 | TWA 5 | <1 | Yes |
SECTION 3 – Physical Data
| Boiling Point | Specific Gravity (H2O=1) | Vapor Pressure | Percent Volital By Volume | Percent Solid By Weight | Vapor Density (AIR=1) | Evaporation Rate | Solubility In Water | Appearance And Odor | Material Is: |
| N/A | <1 | N/A | 0 | 100 | N/A | N/A | N/A | Solid metal pipe with threaded or unthreaded ends | Solid |
SECTION 4 – Fire and Explosion Hazard Data
| Flash Point | None |
| Method Used | N/A |
| Flammable Units | None |
| LEL | N/A |
| UEL | N/A |
| Extinguishing Media | Use Carbon Dioxide, Water or Foam |
| Special Fire Fighting Procedures | If entering a confined area, fire fighters should wear a NOISH approved, Self Contained Breathing Apparatus |
| Unusual Fire and Explosion Hazards | None |
SECTION 5 – Health Hazard Data
| Effects of Overexposure | Effects of overexposure to fumes and dust may produce irritation of eyes and respiratory system. Metallic taste in mouth, dryness of throat and Influenza-Like symptoms. |
| Primary Routes of Entry | Inhalation (X) Skin Contact (__) If mold is fractured |
| Emergency and First Aid Procedures | Flush eyes with water for at least 15 minutes. If exposed to excessive levels of metal fumes, remove to fresh air, seek medical aid immediately. |
SECTION 6 – Reactivity Data
| Stability | Unstable (__) Stable (X) |
| Conditions To Avoid | None |
| Incompatibility (Materials to avoid) | None |
| Hazardous Decomposition Products | None |
| Hazardous Polymerization | May Occur (__) Will Not Occur (X) |
| Conditions To Avoid | None |
SECTION 7 – Spill Or Leak Procedures
| Steps To Be Taken If Material Is Released | N/A |
| Waste Disposal Method | Landfill in accordance with local, state, and federal regulations |
| RCRA Hazardous Waste No. (40 CFR 261.33) | None |
| Volatile Organic Compound (VOC) (As packaged minus water) | None |
SECTION 8 – Special Protection Information
| Respiratory Protection (specify type) | NIOSH/MSHA-Approved dust and fume respirator used to avoid inhalation of particles when exposed. |
| Ventilation | |
| Local Exhaust (specify rate) | Local exhaust ventilation should be used when grinding and machining when exposure exceeds TLV% |
| Special | None |
| Mechanical (general) | None required-normal ventilation adequate |
| Protective Gloves (specify rate) | Should be used when handling |
| Eye Protection (specify rate) (Safety glasses are recommended) | Safety glasses or goggles when grinding or machining |
| Other Protective Equipment | None required |
SECTION 9 – Special Precautions
| Precautions To Be Taken In Handling And Storage | Store in a clean dry place to preserve product quality |
| Other Precautions | Care in handling should be exercised to avoid mechanical injury |
The above information was extracted from Material Safety Data Sheets from our raw material suppliers and is believed to be correct as of the date hereof.
However, no warranty of merchantability, fitness for any use, or any other warranty is express or is to be implied regarding the accuracy of these data, the results to be obtained from the use of the material, or the hazards connected with such use. Since the information contained herein may be applied under conditions beyond our control and with which we may be unfamiliar, and since data made available subsequent to the date hereof may suggest modification of the information, we do not assume responsibility for the results of its use. This information is furnished on the condition that the person receiving its shall make his own determination as to the suitability of the material for his particular purpose and on the condition that he assume the risk of his use thereof.